Calculation of the stress-strain state in a pre-loaded elastoplastic body with the sequential formation of cavities based on the theory of repeated superposition of large deformations
https://doi.org/10.22405/2226-8383-2024-25-4-239-249
Abstract
A numerical solution to the problem of the stress-strain state in a body made of an elastoplastic material with the sequential formation of several cavities in it after preliminary loading at finite deformations has been obtained and studied. To model plasticity, the Mises condition and the law of plastic flow associated with this condition were used. A general mechanical formulation of the problem is given based on the theory of repeated superposition of large deformations. The general solution algorithm is outlined. To solve the problem, we used the finite element method and its modification — the spectral element method. The solution was obtained using methods and algorithms of the engineering strength analysis system. Some results of numerical calculations are presented for the plane static problem of stress concentration in the vicinity of three elliptical cavities formed in a body of square cross-section in the case of plane strain. Effects caused by plasticity, geometric nonlinearity, and redistribution of finite
deformations were studied. The results were compared for cases of sequential and simultaneous formation of cavities.
About the Authors
Vladimir Anatol’evich Levin
Lomonosov Moscow State University
Russian Federation
Russian Federation
doctor of physical and mathematical sciences, professor
Konstantin Moiseevich Zingerman
Tver State University
Russian Federation
Russian Federation
doctor of physical and mathematical sciences, professor
Mikhail Alexandrovich Kartsev
Tula State University
Russian Federation
Russian Federation
postgraduate student
Konstantin Alexandrovich Petrovskii
Lomonosov Moscow State University
Russian Federation
Russian Federation
candidate of physical and mathematical sciences
References
1. Muskhelishvili, N. I. 1963, “Some basic problems of the theory of elasticity”, Noordhof, Groningen, P. 707.
2. Savin, G.N. 1968, “Raspredelenie napryazhenij okolo otverstij. [Stress distribution near holes]”, Kiev: Naukova dumka, 887 p. (in Russian).
3. Levin, V.A., Zubov, L.M., Zingerman, K.M. 2018, “Multiple joined prestressed orthotropic layers under large strains”, International Journal of Engineering Science. V. 133, pp. 47–59.
4. Zingerman, K.M., Levin, V.A. 2009, “Redistribution of finite elastic strains after the formation of inclusions. Approximate analytical solution”, Journal of Applied Mathematics and Mechanics, V. 73, Iss. 6. pp. 710–721. URL: https://doi.org/10.1016/j.jappmathmech.2010.01.011.
5. Levin, V.A., Zingerman, K.M. 2002, “Ploskie zadachi mnogokratnogo nalozheniya bol‘shikh deformaczij. Metody‘ resheniya. [Plane problems of the theory of repeated superposition of large strains: Methods of solution]”, M.: Fizmatlit, 272 p. (in Russian).
6. Zingerman, K.M., Levin, V.A. 2013, “Extension of the Lame–Gadolin problem for large deformations and its analytical solution”, Journal of Applied Mathematics and Mechanics, V. 77, Iss. 2. pp. 235-244. URL: https://doi.org/10.1016/j.jappmathmech.2013.07.016.
7. Levin, V.A., Zingerman, K.M. 1998, “Interaction and microfracturing pattern for successive origination (introduction) of pores in elastic bodies: Finite deformation”, Trans. ASME. J. Appl. Mech. 1998. V. 65. no. 2. pp. 431–435. doi: 10.1115/1.2789072.
8. Levin, V.A., Zingerman, K.M., 2008. "A class of methods and algorithms for the analysis of successive origination of holes in a pre-stressed viscoelastic body. Finite strains Communications in Numerical Methods in Engineering. Vol. 24, Issue 12. pp. 2240–2251. doi: 10.1002/cnm.1080.
9. Levin, V.A., Zingerman, K.M., Vershinin, A.V., Freiman, E.I., Yangirova, A.V. 2013, “Numerical analysis of the stress concentration near holes originating in previously loaded viscoelastic bodies at finite strains”, International Journal of Solids and Structures. V. 50, no. 20–21, pp. 3119– 3135. doi: 10.1016/j.ijsolstr.2013.05.019.
10. Abramov, S.M., Amel’kin, S.A., Kljuev, L.V., Krapivin, K.J., Nozhnickij, J.A., Servetnik, A.N., Chichkovskij, A.A. 2017, “Modeling the development of large plastic deformations in a rotating disk in the Fidesys program”, Chebyshevskii Sbornik. V. 18(3). pp.15-27. (In Russ.) doi: 10.22405/2226-8383-2017-18-3-15-27.
11. Levin, V.A., Zingerman, K.M., Krapivin, K.Yu., Yakovlev, M.Ya. 2020, “Legendre spectral element for plastic localization problems at large scale strains”, Chebyshevskii Sbornik. V. 21(3). pp. 306–316. (In Russ.) doi: 10.22405/2226-8383-2020-21-3-306-316.
12. Levin, V.A., Zingerman, K.M., Krapivin, K.Y. 2023, “Numerical solution of stress concentration problems in elastic-plastic bodies under the superposition of finite deformations”, Advanced Structured Materials. V. 198. pp. 305–323. doi: 10.1007/978-3-031-43210-1_18.
13. Lee E. H. 1969, “Elastic-plastic deformation at finite strains”, Journal of Applied Mechanics. Vol. 36. Iss. 1. pp. 1–6.
14. Mandel, J. 1966, “Contribution theorique a l’etude de l’ecrouissage et des lois de l’ecoulement plastique”, Proceedings of the 11th International Congress on Applied Mechanics. pp. 502–509.
15. Lurie, A.I. 1990, “Nonlinear Theory of Elasticity”, North-Holland, Amsterdam.
16. Simo, J. C., Hughes, T. J. R. 1998, “Computational Inelasticity”, Interdisciplinary Applied Mathematics, Vol. 7. Springer, New York. 392 p.
17. Zienkiewicz, O.C., Taylor, R.L., Fox, D.D. 2014, “The finite element method for solid and structural mechanics”, 7-th edition. Elsevier. 624 p.
18. Levin, V.A., Vershinin, A.V. 2015, “Nelinejnaya vy‘chislitel‘naya mekhanika prochnosti. Tom 2. Chislenny‘e metody‘. Parallel‘ny‘e vy‘chisleniya na E‘VM. [Nonlinear Computational Strength Mechanics. Vol. 2. Numerical Methods. Parallel computing.]”, Pod obshh. red. V.A. Levina. Fizmatlit, Moscow. 544 p. (in Russian).
19. Komatitsch, D., Vilotte, J. P. 1998, “The spectral element method: An efficient tool to simulate the seismic response of 2D and 3D geological structures”, Bull. Seismol. Soc. Am. V. 88, no. 2. pp. 368–392. doi: 10.1785/BSSA0880020368.
20. Konovalov D. Vershinin A., Zingerman K., Levin V. 2017, “The implementation of spectral element method in a CAE system for the solution of elasticity problems on hybrid curvilinear meshes”, Modeling and Simulation in Engineering. V. 2017, art. id. 1797561. doi: 10.1155/2017/1797561.
Review
For citations:
Levin V.A., Zingerman K.M., Kartsev M.A., Petrovskii K.A. Calculation of the stress-strain state in a pre-loaded elastoplastic body with the sequential formation of cavities based on the theory of repeated superposition of large deformations. Chebyshevskii Sbornik. 2024;25(4):239-249. (In Russ.) https://doi.org/10.22405/2226-8383-2024-25-4-239-249
Views:
56
Email this article 