Mathematical optimization of the process of electrodispergation of the waste of the alloy of the residence permit
https://doi.org/10.22405/2226-8383-2021-22-2-389-401
Abstract
setting up a complete factor experiment on the average particle size of the obtained electroerosive materials. The parameters of the EED system operation were selected as factors:
the voltage at the electrodes, the capacity of the discharge capacitors, and the pulse repetition rate. The optimal parameters of the installation were determined for two working media: distilled water and lighting kerosene. According to a series of experiments to determine the maximum value of the parameter optimization in EDM average size of the particles that made up: for water — 51,38 𝜇m when capacity bit of 65.5 𝜇f capacitors, the voltage across the electrodes 210, the pulse repetition frequency of 230 Hz; for kerosene — 61,73 𝜇m when capacity bit of 65.5 𝜇f
capacitors, the voltage across the electrodes 160 and the pulse repetition frequency of 205 Hz.
About the Authors
Ekaterina Vladimirovna Ageeva
Southwestern State University
Russian Federation
Russian Federation
candidate of technical sciences, associate professor
Yevgeniy Viktorovich Ageev
Southwestern State University
Russian Federation
Russian Federation
doctor of technical sciences, professor
Olga Vladimirovna Kuzovleva
Russian State University of Justice
Russian Federation
Russian Federation
candidate of technical sciences, associate professor
Alexandr Evgenievich Gvozdev
Tula State Lev Tolstoy Pedagogical University
Russian Federation
Russian Federation
doctor of technical sciences, professor
References
1. Ageev E.V., Gadalov V.N., Semenikhin B.A., Ageeva E.V., Latypov R.A. 2010, «Obtaining wear-resistant powders from solid alloy waste», Procurement in mechanical engineering, No.12, рp. 39-44.
2. Ageev E.V., Gadalov V.N., Semenikhin B.A., Ageeva E.V., Latypov R.A. 2011, «X-ray Structural analysis of powders obtained by electroerosive dispersion of a hard alloy», Procurement in mechanical engineering, No.2, pp. 42-44.
3. Ageev E.V., Gadalov V.N., Semenikhin B.A., Ageeva E.V., Latypov R.A. 2011, «X-ray Spectral microanalysis of powder particles obtained by electroerosive dispersion of hard alloy»,
4. Strengthening technologies and coatings, No.2(74), pp. 13-16.
5. Ageev E.V., Semenikhin B.A., Ageeva E.V., Latypov RA. 2011, «Evaluation of the effectiveness of the use of hard-alloy powders obtained by electroerosive dispersion of solid-alloy waste in the restoration and strengthening of parts with composite electroplating coatings», Hardening technologies and coatings, No.9(81), pp. 14-16.
6. Ageev E.V., Latypov R.A., Ageeva E.V. 2014, «Investigation of properties of electroerosive powders and hard alloy obtained from them by isostatic pressing and sintering», News of higher
7. educational institutions. Nonferrous metallurgy, No.6, pp. 51-55.
8. Ageeva E.V., Horakova N.M. Ageev E.V. 2014, «Morphology and elemental composition of copper electroerosion powders suitable for sintering», Bulletin of mechanical engineering, No.10, pp. 66-68.
9. Ageeva E.V., Ageev E.V., Vorobyov E.A. 2014, «X-ray Spectral microanalysis of a powder obtained from high-speed steel waste by electroerosive dispersion in kerosene», Bulletin of
10. mechanical engineering, No.11, pp. 71-72.
11. Ageeva E.V., Ageev E.V., Karpenko V.Yu. 2014, «X-ray Structural analysis of a powder obtained from tungsten-containing waste by electroerosive dispersion in an aqueous medium», Bulletin of mechanical engineering, No.12, pp. 64-65.
12. Ageeva E.V., Horyakova N.M., Ageev E.V. 2014, «Investigation of the form and morphology of electroerosive copper powders obtained from waste», Bulletin of mechanical engineering, No.8, pp. 73-75.
13. Ageeva E.V., Horyakova N.M., Ageev E.V. 2014, «Investigation of the size distribution of microparticles in powders obtained by electroerosive dispersion of copper waste», Bulletin of mechanical engineering, No.9, pp. 63-64.
14. Ageev E.V., Ageeva E.V., Vorobiev E.A. 2014, «Granulometric and phase compositions of powder obtained from tungsten-containing waste of tool materials by electroerosive dispersion in kerosene», Hardening technologies and coatings, No.4(112), pp. 11-14.
15. Ageeva E.V., Ageev E.V., Karpenko V.Yu. 2014, «Study of the form and elemental composition of a powder obtained from tungsten-containing waste of tool materials by electroerosive
16. dispersion in an aqueous medium», Hardening technologies and coatings, No.4(112), pp. 14- 17.
17. Horyakova N.M., Ageev E.V., Ageeva E.V. 2014, «Electroerosive copper powders for electroplating coatings», Strengthening technologies and coatings, No.4(112), pp. 18-20.
18. Ageeva E.V., Ageev E.V., Vorobyov E.A., Osminina A.S. 2014, «Obtaining wear-resistant coatings using electrodes from hard-alloy electroerosive powders and their research», Hardening technologies and coatings, No.4(112), pp. 21-23.
19. Ageev E.V., Ageeva E.V., Karpenko V.Yu., Osminina A.S. 2014, «Obtaining hard alloy billets from powders obtained by electroerosive dispersion of tungsten-containing waste», Hardening technologies and coatings, No.4(112), pp. 24-27.
20. Ageeva E.V., Ageev E.V., Horyakova N.M. 2014, «Production of blanks from copper powders obtained by electroerosive dispersion of waste electrical copper and study of their properties», Science-Intensive technologies in mechanical engineering, No.10(40), pp. 10-13.
21. Ageeva E.V., Ageev E.V., Karpenko V.Yu. 2015, «Dimensional analysis of powder particles obtained from tungsten-containing waste by electroerosive dispersion in water», Bulletin of mechanical engineering, No.3, pp. 45-46.
22. Ageeva E.V., Ageev E.V., Vorobiev E.A. 2015, «Analysis of the shape and morphology of powder particles obtained from tungsten-containing waste by electroerosive dispersion in kerosene», Bulletin of mechanical engineering, No.7, pp. 72-73.
23. Ageeva E.V., Latypov R.A., Ageev E.V., Altukhov A.Yu., Karpenko V.Yu. 2015, «Assessment of wear resistance of electric spark coatings obtained using high-speed steel electroerosive powders», News of higher educational institutions. Powder metallurgy and functional coatings,
24. No.1, pp. 71-76.
25. Ageeva E.V., Latypov R.A., Ageev E.V., Altukhov A.Yu., Karpenko V.Yu. 2015, «Characteristics of electric spark coatings obtained by electrodes from high-speed steel electroerosive
26. powders», News of higher educational institutions. Powder metallurgy and functional coatings, No.2, pp. 62-65.
27. Ageeva E.V., Ageev E.V., Latypov R.A. 2015, «Evaluation of wear resistance of electric spark coatings obtained using high-speed steel electroerosive powders», News of higher educational institutions. Powder metallurgy and functional coatings, No.3, p. 45.
28. Ageeva E.V., Horakova N.M. Pikalov, S.V., Ageev E.V. 2015, «Composition, structure and properties of copper spark erosion powder obtained in an environment of kerosene», News of
29. higher educational institutions. Powder metallurgy and functional coatings, No.4, pp. 4-8.
30. Levinson E.M. 1961, Electroerosion treatment of metals. Leningrad, Lenizdat. 184 p.
31. Burtsev V.A., Kalinin N.V., Luchinsky A.V. 1990, Electric explosion of conductors and its application in electrophysical installations. Moscow, Energoatomizdat. 288 p.
32. Gray V.S., Valevich V.V. 1999, «Preparation of highly dispersed metal powders method of electric explosion in the nitrogen of low pressure», Letters to the ZhTF, Vol.25, No.14, pp. 81-84.
33. Holm R. 1961, Electrical contacts. Moscow, Foreign literature Publishing house. 464 p.
Review
For citations:
Ageeva E.V., Ageev Ye.V., Kuzovleva O.V., Gvozdev A.E. Mathematical optimization of the process of electrodispergation of the waste of the alloy of the residence permit. Chebyshevskii Sbornik. 2021;22(2):389-401. (In Russ.) https://doi.org/10.22405/2226-8383-2021-22-2-389-401
Views:
396
Email this article 